gsmilocos

Would you like to react to this message? Create an account in a few clicks or log in to continue.

Share Me


4 posters

    Cyclone Update Post Only HERE!!!

    mAk0y
    mAk0y
    Administrators
    Administrators


    Location : tiendaan laoag
    Posts : 55

    Cyclone Update Post Only HERE!!! Empty Cyclone Update Post Only HERE!!!

    Post by mAk0y Sat Feb 13, 2010 1:51 pm

    Hello,
    New version of Cyclone Box Software is ready. There is a lot of changes, here is some of them:

    Quote:
    - WORLD'S UNIQUE : Standalone Superdongle Key Calculator Added! No internet, no logs, no time! Calculation time - 0.003 sec ! Works for any SL1, SL2 and SL3.

    - WORLD'S UNIQUE : Standalone Unlocking/Relocking using RPL Added! No internet, no logs, no time! Calculation time - 0.002 sec ! Works for any SL1 and SL2.

    - WORLD'S UNIQUE : Standalone SX4 Authorization Added! Box is now emulating Nokia SX4 card - no need internet, no need logs to authorize ANY Nokia Phone, just box! Works for any SL1, SL2 or SL3. Emulated SX4 works with ORIGINAL NOKIA Superdongle keys (no need rebuild SD), Custom keys (made by Cyclone,MT,UB), etc. In case of Authorization fail, it will automaticly write and authorize using Custom Keys. Authoirzation time - 0.004 sec ! Supported are RAP and RAPIDO mcu, in case of RAPU phones SX4 Remote Card will be used. After authorization with Cyclone, PHONE STILL CAN be Authorized with ORIGINAL SX4 Card!

    - WORLD'S UNIQUE - Cyclone can now authorize Barred Phones (with Correct superdongle keys, but with higher KeyIndex ever used than 0 (possible KeyIndex 0..7), SX4 card can use any higher keyindex at time, when higher key is used, lower keys are automaticly not used in future, and phone requires to use higher key index) - UB and other custom boxes can't do it as long SX4 emulation is not 100% Nokia-Like

    - WORLD'S UNIQUE : Starting from now, Cyclone Box have ability to make _FULL RPL BACKUP_ of BB5 phones! Current existing SW on market creating only some part of RPL (NPC,HWC,Simlock) - Cyclone is now backing up missing part:

    - Added SUPER DONGLE KEY extracting (this Original Nokia one, so after writing it back phone still can be authorized with original SX4 card)

    - Added CMLA KEY DATA extracting (That means created RPL File by Cyclone is now 100% SAME AS NOKIA'S ONE!)

    - WORLD'S UNIQUE : Added BB5 MCU & DSP Timestamps Reader / Diagnostic Tool. This will help diagnostic of downgraded phone, will read Security Block, decode timestamps of current installed SW (and factory one, or Dejan Hack if exists) with FLASH installed MCU/DSP timestamps. Will have ability to FULL REBUILD downgrade security zone (dead06) soon.

    - WORLD'S UNIQUE : BB5 Security Block Analyzer added, this will read Security Block and analyze it's health for content of following Security Data: SIMLOCK DATA, SUPERDONGLE KEY DATA, ECC KEYS DATA, DIV DATA, CMLA (DRM) DATA. Also it reads ST_SIMLOCK_TEST and ST_SECURITY_TEST and when problems occur, recommends actions.

    - WORLD'S UNIQUE : Standalone BB5 Calculator Added. This calculated BB5 NCK (levels 1-7) for unlocking purposes. Calculated codes works only with phones which have been relocked with Cyclone Box. To calculate code is needed only IMEI - no need cable, phone, flashbus logger, etc.

    - WORLD'S UNIQUE : BB5 Unlock by NCk/RPL, SD Recalc, SX4 auth using USB !! (once log file readen)

    - Upon box upgrade (maintenance) Bootloader in box is syncronized with server to avoid Activation Problems
    - Bootagent server upgraded to 1.01, fixed "Box is not activated, ID 09)
    - Fixed "Access Violation" when Cyclone Box SW is already launched and connection to box opened
    - After BB5 Relock, unlock codes is displayed
    - More detailed messages is now shown upon new NCK or RPL calculation
    - BB5 Security Code Reading is moved to "UserArea" tab (needed space for MCU/DSP timestamp reading and security block analyzing)
    - Total unlock/relock time added after operation is finished (thx to arash)
    - Box Firmware version is now checked upon loading of Nokia Module - if box firmware is obsolete, SW asks for upgrade and doing it automaticly
    - Selected unlock method is now displayed before RootkeyHash support check
    - Upon first reading of NCK Code (Extracting) or RPL Calculation, "CYC" log file is stored in "StoredFiles" and next time upon BB5 Security Actions (Calculation of SD, Extracting NCK, Calculating RPL (Relocking)) phone is no booted anymore and whole process took only 1 second!! Keep in mind calculated CYC file is paired with Box Serial number, so in case if your box serial number is changed-go to stored files and purge all "cyc" files.
    - Decrypted AES Subblock of Security Block is now checksum checked (16 bytes checksum at end of block)
    - Fixed "This is invalid integer..." when parsing phone with damaged IMEI
    - When another copy of Cyclone Software is running, message is displayed instead of errors
    - New method of NCK Calculation is now default BB5 unlocking method
    - When New Method of NCK calculation is selected, PA_SL is not determined already (saves lots of time)
    - Skin Manager updated to v6.54 (more stability)
    - When BB5 RPL Don't contain Certificates (NPC,HWC) phone isn't booted
    - Fixed bug when Flash RPL BB5 Data is being written two times
    - Added more verbose debug messages when preparing Boot BB5 Phone
    - Garbage characters when dealing with SLPA phones (#pw+___garbage___+1) bug fixed
    - New splash screen added, thx to arash, again
    - When Cyclone fails to boot APE subsystem, it shows hint about TX2
    - APE subsystem is now no longer booted upon CheckFlashingBus
    - Changed "Failed to write CMT Cert Data (3)" message, added TX2 information
    - BB5 TX2 Line test added after "CheckFlashingBus"
    - Before RPL Write, Software testing TX2 Line and when its faulty (not adapter) it showing apporiate message
    - Writing BB5 CMT HWC Certificate from RPL fixed (thx to arash)
    - Parsing some Simlock Arrays (5130) produced garbage output - fixed (thx to arash again)
    - Added support for Cyclone Box HW Rev A11D
    Just download EXE file and replace at C:\Program files\Cyclone Box\
    Make sure Installer is installed aswell (this one from january, else you will have message RootkeyHash not supported).

    You don't need any activations,logs to use this update.

    Notes:
    SX4 Emulation works offline and emulates SX4 card 1:1, in case of failure still server will be used.

    BB5 NCK Calculator works for phone relocked by Cyclone Only (unlocking using IMEI only, no need know other data, just imei - no need cable or connection to box too).

    BB5 USB Unlocking and other security tools works only if phone log (by flashbus) is readen before.

    Update is fast and most of security functions (sd,rpl) works very fast.

    Don't forget to upgrade your Box Firmware to v01.21.

    Download Link : [You must be registered and logged in to see this link.]

    More coming.
    Best Regards,
    Cyclone Team
    lord_sam
    lord_sam
    Bagnet Important Person
    Bagnet Important Person


    Location : KSA RIYADH
    Posts : 134

    Cyclone Update Post Only HERE!!! Empty Re: Cyclone Update Post Only HERE!!!

    Post by lord_sam Sat Feb 13, 2010 3:28 pm

    Dyos ti agngina boss iti pinang paka ammom padakami daytoy. agyamanak unay ti ado ket sapay kuma ta dikay mauma nga agkalap ti pagsayaatan tau dito.


    :bounce: :bounce: :bounce: :bounce: :bounce:
    zhaidave13
    zhaidave13
    Registered Member


    Location : Laoag City
    Posts : 12

    Cyclone Update Post Only HERE!!! Empty Re: Cyclone Update Post Only HERE!!!

    Post by zhaidave13 Sat Feb 13, 2010 4:18 pm

    tnx 4 sharing boss. . . .
    HYPERTEK
    HYPERTEK
    Site Owner
    Site Owner


    Location : Banga Town
    Posts : 3948

    Character sheet
    INCSA:

    Cyclone Update Post Only HERE!!! Empty Re: Cyclone Update Post Only HERE!!!

    Post by HYPERTEK Thu Mar 10, 2011 8:21 am

    Cyclone Box Installer v1.12 Released


    Hi, new installer is ready.

    =====================
    Installer v1.12
    09.03.2011
    =====================
    - Firmware v1.55 introduced - RAP4 CMT Booting (Wrong first char) fixed
    - Added SP unlock via server / log2cod reading
    - Added standalone SX4 auth
    - Added standalone Superdongle Keys Repair
    - Supported phones:
    - RAPU Based: 5630, 6260s, 6700c, 6700s, 6710n, 6720c, 6730, 6750, E52, E55, E72
    - RAP4 Based: 3710, 5330, 7230, 6303i, X3
    - Minor changes and bugfixes

    Download Link: [You must be registered and logged in to see this link.]

    In case of RAP4 mobiles make sure you are using cables with:
    1) *******ted MBUS line 2) Digital ground connectet to analog 3) most possible short, without adapter

    Else - you will get booting problems.

    Best Regards,
    Cyclone Team
    HYPERTEK
    HYPERTEK
    Site Owner
    Site Owner


    Location : Banga Town
    Posts : 3948

    Character sheet
    INCSA:

    Cyclone Update Post Only HERE!!! Empty Re: Cyclone Update Post Only HERE!!!

    Post by HYPERTEK Fri May 06, 2011 10:42 am

    Cyclone!! FREE, STANDALONE UNLOCK/SD REPAIR/SX4 AUTH/SD BACKUP/..FOR ALL NEW BB5 HASH


    Hi, new update for Cyclone Box is ready.

    Reading of LOG file added for all latest hashes and roms using new flashing protocol for RAPU CPU.

    This means you can now:
    - SP Unlock using LOG2COD
    - Repair supedongle keys
    - Backup superdongle key - FIRST AND ONLY IN THE WORLD (no other box support new encryption!)
    - Create RPL from phone - 100% Nokia LIke (with ALL security)
    - Standalone SX4 authorization without SX4 Card (only box)
    - Detailed security analysis
    - Read MCU&DSP Timestamps
    - Others (soon....)

    The new logreading method is simply not related to Rootkey hash.
    If loader is signed for given hash and runs ok - it will work.
    RAPU Loader is signed for following hashes (however most of them even not exists in production, or keys isn't use anymore, but as long as other teams provide this hashes, we will provide it too):

    68597B9162BAB81AF74C56E78EA2588F
    EA81B32860B86EF4231A11831045F3E6
    8E309B54DA1ADDE27C2A035D63AACACD
    916F75217F32081248B15C38DFC8E81B - Nokia X3-02, Nokia C5, Nokia E5, Nokia N8, Nokia C7, Nokia C3-01
    DA550B5BAAB517409088A3E4F3EB53AC
    46802B476C93A05CBAF76A64752086A9*
    25B977A055BE9B5DEC0C38A2A279C695 - 5630, 6260s, 6700c, 6700s, 6710n, 6720c, 6730, 6750, E52, E55, E72
    700370BCF8AFBAB25DD62DBD124FD9CE - Nokia 5630
    87FAC992288DA497A663E5DDC0410B11
    928E5FFB88D81E5F74729A212AB9D12E
    F2D76DFAFD66C7F195F278417DF05888
    F682624FFB08F6D955DBE7D9C0485084
    55DF9CBCC80B17225043DDA1CC783C97

    Of course update is free, we don't ask for any activations, we don't even require internet connection.

    For reading Log file you need valid TX2 enabled cable (otherwise software will hangup upon Getting Configuration!).

    Here is tested with Nokia C5 (thx Moulnisky!)




    Quote:



    Reading SL3 LOG File...
    MCU Version V ICPR82_10w08
    MCU Date 26-02-10
    Product RM-645 (Nokia C5)
    Manufacturer (c) Nokia
    IMEI 354847049967066
    Mastercode 5222614247
    WARNING: "0AC00114AD9C03443A69EAF6BE05ED1B1E10F214.C000249F " Not Exists, Will read it...
    Reading CYC file from phone...
    Booting CMT...
    CMT_SYSTEM_ASIC_ID: 000000030000022600010007600C192102031104
    CMT_EM_ASIC_ID: 00000C35
    CMT_EM_ASIC_ID: 00000C30
    CMT_PUBLIC_ID: 0AC00114AD9C03443A69EAF6BE05ED1B1E10F214
    CMT_ASIC_MODE_ID: 00
    CMT_ROOT_KEY_HASH: 916F75217F32081248B15C38DFC8E81B
    CMT_BOOT_ROM_CRC: E693EF0D
    CMT_SECURE_ROM_CRC: AC22615B
    CMT Ready!
    New_RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.10.48.1, Algo: BB5
    Flashbus Write baud set to 1.0Mbits
    Flashbus Read baud set to 98Kbits
    Using NEW BB5 FLASHING PROTOCOL
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
    FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
    FlashChip[0,CMT]: 0x0020004000000031, ST, NOR
    FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
    FlashChip[0,CMT]: 0x0020004000000031, ST, ONENAND
    Requested Algorithm: XSR 1.6 (CMT)
    Loader: RAPxx CommonBoot v1.02 (C) 2011 Karwos Labs
    Custom loader running OK! Working...
    Readed OK, Saving to "0AC00114AD9C03443A69EAF6BE05ED1B1E10F214.C000249F "
    Success!

    More will come next week probably together with new installer,bugfixes,and features....

    Where from download?

    [You must be registered and logged in to see this link.]

    Box Firmware v1.60 is ORDINARY for this update !

    Best Regards,
    Cyclone Team
    HYPERTEK
    HYPERTEK
    Site Owner
    Site Owner


    Location : Banga Town
    Posts : 3948

    Character sheet
    INCSA:

    Cyclone Update Post Only HERE!!! Empty Re: Cyclone Update Post Only HERE!!!

    Post by HYPERTEK Sun May 08, 2011 5:21 pm

    Cyclone BOMB!! ALL NEW RAPIDO HASH STANDALONE SL2/SL3 UNLOCK / SD REPAIR / SX4 AUTH..

    Hi, new update for Cyclone Box is ready.

    Reading of LOG file added for all latest hashes and roms using new flashing protocol for RAPIDO CPU.

    This means you can now:
    - SP Unlock using LOG2COD (SL3 phones)
    - Direct SP unlock of SL2 479cc.. based mobiles using NCK calculation
    - Direct SP unlock of SL2 479cc.. based mobiles using RPL calculation
    - Repair supedongle keys
    - Create RPL from phone - 100% Nokia LIke (with ALL security)
    - Standalone SX4 authorization without SX4 Card (only box)
    - Detailed security analysis
    - Read MCU&DSP Timestamps
    - Others (soon....)

    The new logreading method is simply not related to Rootkey hash.
    If loader is signed for given hash and runs ok - it will work.
    RAPIDO Loader is signed for following hashes (however most of them even not exists in production, or keys isn't use anymore, but as long as other teams provide this hashes, we will provide it too):

    68597B9162BAB81AF74C56E78EA2588F
    EA81B32860B86EF4231A11831045F3E6
    8E309B54DA1ADDE27C2A035D63AACACD
    916F75217F32081248B15C38DFC8E81B
    DA550B5BAAB517409088A3E4F3EB53AC
    B8C3ADECFC997FCD8081D3DEAF870B8C
    479C6DDE3942E12C429C1D6ADED80371
    C70CB07324056BC66A824347F40DB2D5
    B1A9CEADB5CE9CF9FB4F442150AA8E09
    46802B476C93A05CBAF76A64752086A9
    1B0D74C532CA1C6133940C740E8C786E
    25B977A055BE9B5DEC0C38A2A279C695
    700370BCF8AFBAB25DD62DBD124FD9CE
    9DDBFCFE6E73CED7D8C6268C8EB85723
    7B045400E1752022F9EB80B0DEA9C65D
    928E5FFB88D81E5F74729A212AB9D12E
    F2D76DFAFD66C7F195F278417DF05888
    CAEEBB65D3C48E6DC73B49DC5063A2EE
    FCB5C510AF7F09F313D9BDE85A707CC0
    9A28E119033B91D14D22838C86D0D53C
    F682624FFB08F6D955DBE7D9C0485084
    55DF9CBCC80B17225043DDA1CC783C97
    38F312750F686F9FC9B1B3778774A195
    BAF3A9C3DBFA8454937DB77F2B8852B1
    A5404AE83A594ECADEE532F0C236BFA6
    E9EFF4BFAA5393217CA6B17755FC3E14

    Of course update is free, we don't ask for any activations, we don't even require internet connection.
    For reading Log file you need valid TX2 enabled cable (otherwise software will hangup upon Getting Configuration!).

    Here is tested with Nokia 5800-SL3-479cc (thx Moulnisky!)




    Quote:



    Reading SL3 LOG File...
    MCU Version V ICPR72_09w20.15
    MCU Date 30-12-09
    Product RM-356 (Nokia 5800 XpressMusic)
    Manufacturer (c) Nokia
    IMEI 352012047692891
    Mastercode 413074336
    WARNING: "05C00008DF1F00527E9AEF53D8B8ACEC8C185116.C0000607 " Not Exists, Will read it...
    Reading CYC file from phone...
    Booting CMT...
    CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101051103
    CMT_EM_ASIC_ID: 00000296
    CMT_EM_ASIC_ID: 00000B22
    CMT_PUBLIC_ID: 05C00008DF1F00527E9AEF53D8B8ACEC8C185116
    CMT_ASIC_MODE_ID: 00
    CMT_ROOT_KEY_HASH: 479C6DDE3942E12C429C1D6ADED80371
    CMT_BOOT_ROM_CRC: 4B9B7510
    CMT_SECURE_ROM_CRC: 3E691FF8
    CMT Ready!
    New_RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.48.1, Algo: BB5
    Flashbus Write baud set to 1.0Mbits
    Flashbus Read baud set to 98Kbits
    Using NEW BB5 FLASHING PROTOCOL
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
    FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
    FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
    FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
    FlashChip[0,CMT]: 0x00EC004000000121, Samsung, ONENAND
    Requested Algorithm: XSR 1.5 (CMT)
    Sending Auxiliary Loader...
    Auxiliary Loader Sent!
    Loader: RAPxx CommonBoot v1.03 (C) 2011 Karwos Labs
    Custom loader running OK! Working...
    Readed OK, Saving to "05C00008DF1F00527E9AEF53D8B8ACEC8C185116.C0000607 "
    Success!

    Where from download?

    [You must be registered and logged in to see this link.]

    Box Firmware v1.60 is ORDINARY for this update !

    Best Regards,
    Cyclone Team
    HYPERTEK
    HYPERTEK
    Site Owner
    Site Owner


    Location : Banga Town
    Posts : 3948

    Character sheet
    INCSA:

    Cyclone Update Post Only HERE!!! Empty Re: Cyclone Update Post Only HERE!!!

    Post by HYPERTEK Wed May 11, 2011 11:25 am

    Cyclone STOP THE UNSTOPPABLE!! NEW RAPIDO ENCRYPTION, 1ST SD/CMLA/SX BACKUP, MORE!!!!


    Hi to all, new Update for Cyclone Box is Ready.
    We are sorry for problems caused by previous release.
    In this version we implemented new encryption routines for New MCU RAPIDO Phones. That means you can now:

    - Read correct LOG file for SL3 SP Unlock (sorry, discard previous ones!)
    - Direct SP Unlock of SL2 New hash (479cc based) phones (6760, 6120c) using NCK Calculation
    - Direct SP Unlock of SL2 New hash (479cc based) phones (6760, 6120c) using RPL Calculation
    - Absolutly FIRST IN THE WORLD - Superdongle Key Backup for new hash - no other tool support it
    - Absolutly FIRST IN THE WORLD - Standalone SX4 authorization without Superdongle key corruption
    - Absolutly FIRST IN THE WORLD - CMLA/WMDRM Key backup
    - Absolutly FIRST IN THE WORLD - 1:1 Original Nokia RPL Backup (w/o risk of DAMAGING phones!)
    - Security analysis
    - The new encryption works also for old rapido phones (CAEEBB based) which noone tool could properly decrypt Superdongle/etc data
    - More ..

    Supported hashes:

    68597B9162BAB81AF74C56E78EA2588F
    EA81B32860B86EF4231A11831045F3E6
    8E309B54DA1ADDE27C2A035D63AACACD
    916F75217F32081248B15C38DFC8E81B
    DA550B5BAAB517409088A3E4F3EB53AC
    B8C3ADECFC997FCD8081D3DEAF870B8C
    479C6DDE3942E12C429C1D6ADED80371
    C70CB07324056BC66A824347F40DB2D5
    B1A9CEADB5CE9CF9FB4F442150AA8E09
    46802B476C93A05CBAF76A64752086A9
    1B0D74C532CA1C6133940C740E8C786E
    25B977A055BE9B5DEC0C38A2A279C695
    700370BCF8AFBAB25DD62DBD124FD9CE
    9DDBFCFE6E73CED7D8C6268C8EB85723
    7B045400E1752022F9EB80B0DEA9C65D
    928E5FFB88D81E5F74729A212AB9D12E
    F2D76DFAFD66C7F195F278417DF05888
    CAEEBB65D3C48E6DC73B49DC5063A2EE
    FCB5C510AF7F09F313D9BDE85A707CC0
    9A28E119033B91D14D22838C86D0D53C
    F682624FFB08F6D955DBE7D9C0485084
    55DF9CBCC80B17225043DDA1CC783C97
    38F312750F686F9FC9B1B3778774A195
    BAF3A9C3DBFA8454937DB77F2B8852B1
    A5404AE83A594ECADEE532F0C236BFA6
    E9EFF4BFAA5393217CA6B17755FC3E14

    And small tests

    Nokia 6760 479CC Direct unlock




    Quote:



    BB5 Unlock Started...
    MCU Version V 09w17.03.45
    MCU Date 20-10-09
    Product RM-573 (Nokia 6760 Slide)
    Manufacturer (c) Nokia
    IMEI 355203035769745
    Mastercode 461474133
    Simlock Server SIMLOCK SERVER
    Simlock Key 5050200000000000
    Simlock Profile 8000000000000000
    Simlock Key Cnt 1
    Simlock FBUS Cnt 8
    Simlock [1,1] State: CLOSED Type: MCC-MNC Data: 50502F
    Reading Security Block...
    Security block OK and saved to "RM-573_355203035769745_5112011_60929 AM.SecurityBlock.PM"
    "16200007748E005298591CBC3DA4B4F4FEF358A2.C0005311 " Exists, That is good...
    WARNING: Stored CYC file is probably corrupted
    Reading CYC file from phone...
    Booting CMT...
    CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101051103
    CMT_EM_ASIC_ID: 00000296
    CMT_EM_ASIC_ID: 00000B22
    CMT_PUBLIC_ID: 16200007748E005298591CBC3DA4B4F4FEF358A2
    CMT_ASIC_MODE_ID: 00
    CMT_ROOT_KEY_HASH: 479C6DDE3942E12C429C1D6ADED80371
    CMT_BOOT_ROM_CRC: 4B9B7510
    CMT_SECURE_ROM_CRC: 3E691FF8
    CMT Ready!
    New_RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.48.1, Algo: BB5
    Flashbus Write baud set to 1.0Mbits
    Flashbus Read baud set to 98Kbits
    Using NEW BB5 FLASHING PROTOCOL
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
    FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
    FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
    FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
    FlashChip[0,CMT]: 0x00EC004000000121, Samsung, ONENAND
    Requested Algorithm: XSR 1.5 (CMT)
    Sending Auxiliary Loader...
    Auxiliary Loader Sent!
    Loader: RAPxx CommonBoot v1.04 (C) 2011 KarwosLabs
    Custom loader running OK! Working...
    Readed OK, Saving to "16200007748E005298591CBC3DA4B4F4FEF358A2.C0005311 "
    Checking for Rootkey Hash support with selected Unlock Method...
    Selected Unlock Method: NCK Calculation (new method)
    Performing new SL2 Algo...
    #pw+238228650439154+1#
    #pw+976749305397276+2#
    #pw+510431019060809+3#
    #pw+978446698302394+4#
    #pw+744747389804508+5#
    #pw+645730839742156+6#
    #pw+867417704847922+7#
    Sending NCK Codes..
    NCK[1] - ACCEPTED
    NCK[2] - Too fast between tries (bruteforce protection)
    NCK[3] - Too fast between tries (bruteforce protection)
    NCK[4] - Too fast between tries (bruteforce protection)
    NCK[5] - Too fast between tries (bruteforce protection)
    NCK[6] - Too fast between tries (bruteforce protection)
    NCK[7] - Too fast between tries (bruteforce protection)
    MCU Version V 09w17.03.45MCU Date 20-10-09
    Product RM-573 (Nokia 6760 Slide)
    Manufacturer (c) Nokia
    IMEI 355203035769745
    Mastercode 461474133
    Simlock Server SIMLOCK SERVER
    Simlock Key 5050200000000000
    Simlock Profile 8000000000000000
    Simlock Key Cnt 0
    Simlock FBUS Cnt 0
    Simlock [1,1] State: OPENED Type: MCC-MNC Data: 50502F
    Simlock NCK #pw+238228650439154+1#
    Unlock finished! Time taken 12.219s

    5230 Standalone SX4 Auth + security analyze



    Quote:



    MCU Version V ICPR72_10w04.5
    MCU Date 22-03-10
    Product RM-588 (Nokia 5230)
    Manufacturer (c) Nokia
    IMEI 353763044825673
    Mastercode 4253371033
    IMEI Spare 3A35670344286507
    IMEI SV 3335670344286517F1000000
    CNT 20.0.005_001_U389
    PSN 01458E4AA
    Product Code 059B139
    Module Code 0204359
    Basic Product Code 0584528
    PSD 0000000000000000
    LPSN 0
    APE SW V 20.0.005
    APE Variant V 20.0.005V 20.0.005 20.0.005.389.01
    APE Test rm588_ENO_x_09wk43v0.050
    APE HW 256
    APE ADSP 256
    RETU 16
    TAHVO 22
    AHNE 11
    HW 0512
    RFIC 17141716
    DSP simon_ICPR72_10w05
    Simlock Server SIMLOCK SERVER
    Simlock Key 2140700000000000
    Simlock Profile 8000000000000000
    Simlock Key Cnt 0
    Simlock FBUS Cnt 0
    Simlock [1,1] State: OPENED Type: MCC-MNC Data: 21407F
    Simlock [2,1] State: OPENED Type: MCC-MNC Data: 21402F
    Simlock NCK #pw+6SHl74219804726+1#
    Started Phone Security Analysis...
    MCU Version V ICPR72_10w04.5
    MCU Date 22-03-10
    Product RM-588 (Nokia 5230)
    Manufacturer (c) Nokia
    IMEI 353763044825673
    Mastercode 4253371033
    Reading Security Block...
    Security block OK and saved to "RM-588_353763044825673_10052011_221449.SecurityBlock. PM"
    Step 1 : Testing SIMLOCK
    SIMLOCK SEFLTEST PASSED OK!
    Step 2 : Testing SECURITY
    SECURITY SEFLTEST PASSED OK!
    Step 3 : Analyzing Security Block
    WARNING: "1CC001140C9B005273D956C28676BF92A6877017.C0000805 " Not Exists, Will read it...
    Reading CYC file from phone...
    Booting CMT...
    CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101051103
    CMT_EM_ASIC_ID: 00000296
    CMT_EM_ASIC_ID: 00000B22
    CMT_PUBLIC_ID: 1CC001140C9B005273D956C28676BF92A6877017
    CMT_ASIC_MODE_ID: 00
    CMT_ROOT_KEY_HASH: 479C6DDE3942E12C429C1D6ADED80371
    CMT_BOOT_ROM_CRC: 4B9B7510
    CMT_SECURE_ROM_CRC: 3E691FF8
    CMT Ready!
    New_RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.48.1, Algo: BB5
    Flashbus Write baud set to 1.0Mbits
    Flashbus Read baud set to 98Kbits
    Using NEW BB5 FLASHING PROTOCOL
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
    FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
    FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
    FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
    FlashChip[0,CMT]: 0x00EC004000000231, Samsung, ONENAND
    Requested Algorithm: XSR 1.6 (CMT)
    Sending Auxiliary Loader...
    Auxiliary Loader Sent!
    Loader: RAPxx CommonBoot v1.04 (C) 2011 KarwosLabs
    Custom loader running OK! Working...
    Readed OK, Saving to "1CC001140C9B005273D956C28676BF92A6877017.C0000805 "
    Checking SUPERDONGLE...
    SUPERDONGLE FOUND AND CHECKSUM OK! PASSED!
    Checking SIMLOCK...
    Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
    Checking MCU&DSP TIMESTAMPS...
    MCU&DSP TIMESTAMPS FOUND AND CHECKSUM OK! PASSED!
    Checking CMLA KEYS...
    CMLA KEYS FOUND AND CHECKSUM OK! PASSED!
    Checking ECC KEYS...
    ECC KEYS FOUND AND CHECKSUM OK! PASSED!
    Checking DIV KEYS...
    DIV KEYS FOUND AND CHECKSUM OK! PASSED!
    Analyze finished!
    SX4 Authorization / SD Repair Procedure Started....
    "1CC001140C9B005273D956C28676BF92A6877017.C0000805 " Exists, That is good...
    MCU Version V ICPR72_10w04.5
    MCU Date 22-03-10
    Product RM-588 (Nokia 5230)
    Manufacturer (c) Nokia
    IMEI 353763044825673
    Mastercode 4253371033
    Reading Security Block...
    Security block OK and saved to "RM-588_353763044825673_10052011_221503.SecurityBlock. PM"
    SX4 Status: Not authorized (74)
    Started mutual authenthication with card...
    Receiving Phone Seed 1...
    Phone Seed 1 Received
    Sending calculated Data 1, and expecting Seed 2...
    Calculated Data 1 accepted, Phone Seed 2 Received
    Sending calculated Data 2
    Calculated Data 2 sent, Checking Authorization Status again
    Authorization successfully finished!
    Looking for Virgin PM In Database...
    Found, writing...
    [1,0] Written, Length: 114 bytes, Status: OK
    [1,2] Written, Length: 98 bytes, Status: OK
    [1,4] Written, Length: 110 bytes, Status: OK
    [1,6] Written, Length: 98 bytes, Status: OK
    [1,8] Written, Length: 110 bytes, Status: OK
    [1,13] Written, Length: 98 bytes, Status: OK
    [1,16] Written, Length: 98 bytes, Status: OK
    [1,18] Written, Length: 98 bytes, Status: OK
    [1,20] Written, Length: 98 bytes, Status: OK
    [1,22] Written, Length: 16 bytes, Status: OK
    [1,23] Written, Length: 4 bytes, Status: OK
    [1,24] Written, Length: 84 bytes, Status: OK
    [1,25] Written, Length: 4 bytes, Status: OK
    [1,26] Written, Length: 110 bytes, Status: OK
    [1,28] Written, Length: 98 bytes, Status: OK
    [1,29] Written, Length: 10 bytes, Status: OK
    [1,31] Written, Length: 98 bytes, Status: OK
    [1,33] Written, Length: 36 bytes, Status: OK
    [1,34] Written, Length: 80 bytes, Status: OK
    [1,35] Written, Length: 16 bytes, Status: OK
    [1,37] Written, Length: 4 bytes, Status: OK
    [1,39] Written, Length: 36 bytes, Status: OK
    [1,44] Written, Length: 182 bytes, Status: OK
    [1,45] Written, Length: 182 bytes, Status: OK
    [2,0] Written, Length: 448 bytes, Status: OK
    [309,0] Written, Length: 4 bytes, Status: OK
    [309,1] Written, Length: 2 bytes, Status: OK
    [309,2] Written, Length: 12 bytes, Status: OK
    [309,4] Written, Length: 12 bytes, Status: OK
    [309,5] Written, Length: 12 bytes, Status: OK
    [309,7] Written, Length: 12 bytes, Status: OK
    [309,8] Written, Length: 12 bytes, Status: OK
    [309,17] Written, Length: 12 bytes, Status: OK
    Write PM Finished, Record written OK: 33, Record written NOT OK: 0

    Nokia X6



    Quote:



    MCU Version V ICPR72_10w04.5
    MCU Date 22-03-10
    Product RM-559 (Nokia X6)
    Manufacturer (c) Nokia
    IMEI 352006046910791
    Mastercode 134767774
    IMEI Spare 3A25000664197009
    IMEI SV 3325000664197019F4000000
    CNT v 001_000, 17-03-10, vanilla, RM559rRM559_002_001_M004,
    PSN CSF672051
    Product Code 059B8W2
    Basic Product Code 0589312
    PSD 0000000000000000
    LPSN 0
    WLAN MAC A04E047F2AB8
    APE SW V 20.0.005
    APE Variant V 20.0.005V 20.0.005 20.0.005.360.02
    APE Test rm559_ENO_A_09wk28v0.440
    APE HW 256
    APE ADSP 256
    RETU 16
    TAHVO 22
    AHNE 11
    HW 1123
    RFIC |Vapaus_5.1 | Aura_?.?
    DSP ICPR72_10w05
    Simlock Server SIMLOCK SERVER
    Simlock Key 2140400086388183
    Simlock Profile 8000000000000000
    Simlock Key Cnt 0
    Simlock FBUS Cnt 0
    Simlock [1,1] State: OPENED Type: MCC-MNC Data: 21404F
    Simlock NCK #pw+>FKT72534805121+7#
    Started Phone Security Analysis...
    MCU Version V ICPR72_10w04.5
    MCU Date 22-03-10
    Product RM-559 (Nokia X6)
    Manufacturer (c) Nokia
    IMEI 352006046910791
    Mastercode 134767774
    Reading Security Block...
    Security block OK and saved to "RM-559_352006046910791_10052011_220737.SecurityBlock. PM"
    Step 1 : Testing SIMLOCK
    SIMLOCK SEFLTEST PASSED OK!
    Step 2 : Testing SECURITY
    SECURITY SEFLTEST PASSED OK!
    Step 3 : Analyzing Security Block
    WARNING: "1A60010D468C0052CBA704F8193E26C1B8325289.C0000805 " Not Exists, Will read it...
    Reading CYC file from phone...
    Booting CMT...
    CMT_SYSTEM_ASIC_ID: 000000010000022600010006400C192101051103
    CMT_EM_ASIC_ID: 00000296
    CMT_EM_ASIC_ID: 00000B22
    CMT_PUBLIC_ID: 1A60010D468C0052CBA704F8193E26C1B8325289
    CMT_ASIC_MODE_ID: 00
    CMT_ROOT_KEY_HASH: 479C6DDE3942E12C429C1D6ADED80371
    CMT_BOOT_ROM_CRC: 4B9B7510
    CMT_SECURE_ROM_CRC: 3E691FF8
    CMT Ready!
    New_RAPIDOv11_2nd.fg, Type: 2nd Boot Loader, Rev: 512.10.48.1, Algo: BB5
    Flashbus Write baud set to 1.0Mbits
    Flashbus Read baud set to 98Kbits
    Using NEW BB5 FLASHING PROTOCOL
    Default Transmission Mode Requested by Loader: Dual Line, 32 bit, Overriding
    Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
    Box TX2 Data Pin set to: Service Pin 3
    FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
    FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
    FlashChip[0,CMT]: 0x0400000000000000, Unknown, NOR
    FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
    FlashChip[0,CMT]: 0x00EC005800000121, Samsung, ONENAND
    Requested Algorithm: XSR 1.6 (CMT)
    Sending Auxiliary Loader...
    Auxiliary Loader Sent!
    Loader: RAPxx CommonBoot v1.04 (C) 2011 KarwosLabs
    Custom loader running OK! Working...
    Readed OK, Saving to "1A60010D468C0052CBA704F8193E26C1B8325289.C0000805 "
    Checking SUPERDONGLE...
    SUPERDONGLE FOUND AND CHECKSUM OK! PASSED!
    Checking SIMLOCK...
    Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
    Checking MCU&DSP TIMESTAMPS...
    MCU&DSP TIMESTAMPS FOUND AND CHECKSUM OK! PASSED!
    Checking CMLA KEYS...
    CMLA KEYS FOUND AND CHECKSUM OK! PASSED!
    Checking ECC KEYS...
    ECC KEYS FOUND AND CHECKSUM OK! PASSED!
    Checking DIV KEYS...
    DIV KEYS FOUND AND CHECKSUM OK! PASSED!
    Analyze finished!

    Where from download?
    [You must be registered and logged in to see this link.]

    (Firmware v1.61 required)

    Best Regards, [You must be registered and logged in to see this image.]
    Cyclone Team
    HYPERTEK
    HYPERTEK
    Site Owner
    Site Owner


    Location : Banga Town
    Posts : 3948

    Character sheet
    INCSA:

    Cyclone Update Post Only HERE!!! Empty Re: Cyclone Update Post Only HERE!!!

    Post by HYPERTEK Mon May 23, 2011 6:51 pm

    [You must be registered and logged in to see this image.]

    NOTE :
    This is Server Side Update ,So you dont have to do anything just enjoy calculating new meps with CycloneBox [You must be registered and logged in to see this image.]



    br
    CycloneBox Team
    HYPERTEK
    HYPERTEK
    Site Owner
    Site Owner


    Location : Banga Town
    Posts : 3948

    Character sheet
    INCSA:

    Cyclone Update Post Only HERE!!! Empty Re: Cyclone Update Post Only HERE!!!

    Post by HYPERTEK Fri Jun 03, 2011 12:05 pm

    CycloneBox BlackBerry New Secuirty Mep Added





    NOTE 


    This is server side update so you dont have to do anything






    [You must be registered and logged in to see this image.]

    HYPERTEK
    HYPERTEK
    Site Owner
    Site Owner


    Location : Banga Town
    Posts : 3948

    Character sheet
    INCSA:

    Cyclone Update Post Only HERE!!! Empty Re: Cyclone Update Post Only HERE!!!

    Post by HYPERTEK Mon Jun 20, 2011 11:29 am

    Cyclone Box Installer v1.15 Released


    Hi, new update for Cyclone Box is Ready.
    What's new ?




    Quote:



    =====================
    Installer v1.15
    18.06.2011
    =====================
    - Added READING DCT4+/XGold1 Encrypted Security Code from DCT4+ Based phone (previously shown as Crypted DCT4+) - of course WITHOUT data loss - seems 1st in the world
    - Added RESET (to 12345) DCT4+/XGold1 Encrypted Security Code from DCT4+ Based phone - of course WITHOUT data loss - seems 1st in the world
    - Added Reading Full RPL (NPC,CCC,HWC,SIMLOCK,SD,...) from Dead/Downgraded/Security Wrong BB5 Units - seems 1st in world. If phone doesn't power on (Stuck on Nokia logo, or completly dead), you can now dump full RPL file in order to Full Erase your phone and revive it. Softwar before dumping RPL in Recovery mode, will ask user of doing so. So in any case of reviving downgraded phone is:
    1. Create RPL from Dead Phone
    2. Full Erase
    3. Write any SW version
    4. Write previously backed-up RPL file
    5. Authorize with SuperDongle
    6. Write virgin PM
    - Added (fixed) NCK Counter Reset for XGold2 based phones
    - SecurityBlock is now backed-up before NCK Counters Reset, just in case
    - XGold1 Dead units booting fixed
    - Separate button for Receiving L7 Code for LBF added
    - Fixed DCT4 Security Counter Attempts Reset for some DCT4 variants
    - PMM Managment Tab added to BB5 Security Tab
    - Auto-Imei RESTORE added. Used if you have corrupted your imei, but having valid NPC file. Will scan StoredFiles for CRT file matching with CMT Public ID and automaticlly write it.
    - Added DCC camera Hardware Fault alert on DCC repair - some units is hardware fault and repair is not possible (DCC file not found)
    - XGold1 PMM parsing fixed (While reading LBF, Simlock table not found for some operators/phones)
    - XGold2 Flashing problems fixed (Invalid pointer)
    - USB transactions module rewritten
    - Full Erase button added for BB5 mobiles. No need to know FlashChip mapping and size - it's scanned automaticlly. It will erase CMT flash completly. Make sure RPL and PM is readed before erase!!!
    - Added "Just NPC" option used with "Erase Certificates". Used to delete only NPC certificate (corrupt IMEI and switch phone-on to make necessary job ... with IMEI corrupted phone will switch on even without valid security area). You can use this function to dump PM from non-working phone. Don't forget to CREATE RPL FROM PHONE first! Else you will get corrupted IMEI.
    - "Force Use Server" added for SX4 Authorization.
    - Fixed AutoSelecting bug
    - Fixed problem with parsing DCT4 variants when no DCT4 products installed
    - Fixed problem with parsing BB5 variants when no BB5 products installed
    - Index out of bound (0) fixed
    - Plain RPL is checked now by default
    - Removed "Bootloader upgrade problem" message, as caused too much confusion
    - Security Problem #1 and #2 Fixed (anti-idiot-fix)
    - Added additional Security Problem #5 message for Reinstall Drivers
    - Minor changes and bugfixes

    Where from download?
    [You must be registered and logged in to see this link.]

    Best Regards & Stay Tuned,
    Cyclone Box Team
    HYPERTEK
    HYPERTEK
    Site Owner
    Site Owner


    Location : Banga Town
    Posts : 3948

    Character sheet
    INCSA:

    Cyclone Update Post Only HERE!!! Empty Re: Cyclone Update Post Only HERE!!!

    Post by HYPERTEK Wed Jun 22, 2011 11:55 am

    Cyclone Box Update Again, Standalone Blackberry MEP1,MEP2,MEP3,MEP4,MEP5 CALC ADDED


    Hi,




    Quote:



    - Blackberry Module is standalone now, no need server connection
    - MEP List combobox updated (237 meps), if not supported - type manually
    - Added MEP-1 (SIM Card) to Requested MEP gro*****
    - Added MEP-3 (Network Subset) to Requested MEP gro*****
    - Added MEP-5 (Corporate) to Requested MEP gro*****
    - Box firmware v01.63 is required
    - After activating new firmware, box have internal 50 phones limit counter for security reasons. Each calculation drops counter. After reaching 0, Blackberry and XGold (use same slot) service is simply deactivated. To make it working again - just upgrade your box by Box Maintenance again - no re-activation fees, at all.

    Where from download?
    [You must be registered and logged in to see this link.]

    1. Make sure you've installed Installer v1.15 installed first
    2. Upgrade your box firmware to v1.63

    Best Regards & Stay Tuned,
    Cyclone Team[You must be registered and logged in to see this image.]
    HYPERTEK
    HYPERTEK
    Site Owner
    Site Owner


    Location : Banga Town
    Posts : 3948

    Character sheet
    INCSA:

    Cyclone Update Post Only HERE!!! Empty Re: Cyclone Update Post Only HERE!!!

    Post by HYPERTEK Wed Jul 20, 2011 12:21 pm

    Cyclone Box Firmware v01.66 Released

    Hi, this is server-side update only, upgrade your box using Box Maintenance.

    - MEP-31845-002 - added
    - MEP-41261-001 - added
    - MEP-42517-001 - added
    - MEP-08589-001 - fixed NCK length
    - Changed default SX4 Emulation Serial Number due to blacklist by Nokia in latest PA_SD. Now SX4 serial is calculated using box unique OTP Area, so quite randomfull and further blacklist not possible too.
    - Minor Changes and bugfixes

    Best regards N Stay Tuned,
    Cyclone Team
    HYPERTEK
    HYPERTEK
    Site Owner
    Site Owner


    Location : Banga Town
    Posts : 3948

    Character sheet
    INCSA:

    Cyclone Update Post Only HERE!!! Empty Re: Cyclone Update Post Only HERE!!!

    Post by HYPERTEK Mon Sep 26, 2011 5:27 pm

    CycloneBox BlackBerry Module Update(25-09-2011)

    Hi, new update for Cyclone Box BlackBerry Module is ready.


    Added support for following MEPs:

    MEP-06041-012
    MEP-06041-013
    MEP-14074-004
    MEP-29080-003
    MEP-34870-002





    NOTE
    Just update your box using Box Maintenance. Each box having 3 update credits.




    Still alot more to come so stay tune [You must be registered and logged in to see this image.]



    Best Regards,
    Cyclone Team
    [You must be registered and logged in to see this image.]
    HYPERTEK
    HYPERTEK
    Site Owner
    Site Owner


    Location : Banga Town
    Posts : 3948

    Character sheet
    INCSA:

    Cyclone Update Post Only HERE!!! Empty Re: Cyclone Update Post Only HERE!!!

    Post by HYPERTEK Fri Oct 21, 2011 8:40 pm

    Cyclone Box v1.0.0.11671 Released


    Hi, new update is released.

    - Added PA_SIMLOC30 Original Nokia RPL Write support in SIMLOCK2 format

    - The NCK length is now automatically recognized upon RPL write, so correct NCK array lenght might be assumed
    - Minor changes and bugfixes

    Autoupdate should do the job, in case of any problems (or interrupted update) you can manually download exe from
    [You must be registered and logged in to see this link.] and place in C:\Program Files\Cyclone Box\

    Best Regards,

    [You must be registered and logged in to see this link.]
    HYPERTEK
    HYPERTEK
    Site Owner
    Site Owner


    Location : Banga Town
    Posts : 3948

    Character sheet
    INCSA:

    Cyclone Update Post Only HERE!!! Empty Re: Cyclone Update Post Only HERE!!!

    Post by HYPERTEK Mon Nov 07, 2011 11:20 am

    CycloneBox BlackBerry Update (MEP-06041-017)

    CycloneBox Firmware 01.79 Firmware is Ready on server

    Added Latest BlackBerry Security Mep
    MEP-06041-017


    Update your Box from Maintenance tool


    PS
    We know that you guys are waiting for something ,So we will be back again in few hours [You must be registered and logged in to see this image.]
    Stay Tune

    HYPERTEK
    HYPERTEK
    Site Owner
    Site Owner


    Location : Banga Town
    Posts : 3948

    Character sheet
    INCSA:

    Cyclone Update Post Only HERE!!! Empty Re: Cyclone Update Post Only HERE!!!

    Post by HYPERTEK Sat Nov 12, 2011 5:25 pm

    Cyclone Box Broadcom Unlocker Released


    Hi, new update for Cyclone Box is ready.

    Added support for reading Unique Data files for Broadcom 21351 based Nokia Phones (X2, C3, .. and more of them).

    After read Unique Data you can:
    - Unlock SP locks by reading LBF data
    - Backup FULL RPL (including superdonlge) 100% Nokia-Like
    - Repair corrupted Superdongle keys
    - Authorize your phone with SX4 emulation inside box
    - Detailed Security Analysis
    - Downgrade this phones
    - More ...

    X2 Example Uni Data read and Security operation




    Quote:



    Started Phone Security Analysis...
    [Nokia X2-00 USB Phonet]: Port opened OK!
    MCU Version V 04.90
    MCU Date 28-09-10
    Product RM-618 (Nokia X2-00)
    Manufacturer (c) Nokia
    IMEI 352699049966024
    Mastercode 554352325
    Reading Security Block...
    Security block OK and saved to "RM-618_352699049966024_2011-11-12_132245.SecurityBlock.PM"
    Step 1 : Testing SIMLOCK
    SIMLOCK SEFLTEST PASSED OK!
    Step 2 : Testing SECURITY
    SECURITY SEFLTEST PASSED OK!
    Step 3 : Analyzing Security Block
    WARNING: "48400406073ECC4443B83B4151F972ABA08B3D66.C0003160 " Not Exists, Will read it...
    Reading CYC file from phone...
    Booting CMT...
    [Nokia X2-00 USB Phonet]: Port opened OK!
    Switching to RAW Mode...
    [Nokia USB Flashing Generic]: Port opened OK!
    New ROM Detected
    CMT_SYSTEM_ASIC_ID: 000000000000000022000509200C0000
    CMT_EM_ASIC_ID: 00005361
    CMT_PUBLIC_ID: 48400406073ECC4443B83B4151F972ABA08B3D66
    CMT_ASIC_MODE_ID: 00
    CMT_ROOT_KEY_HASH: 1B0D74C532CA1C6133940C740E8C786E
    CMT_BOOT_ROM_CRC: DE56D582
    CMT_SECURE_ROM_CRC: BDDE7A3A
    CMT Ready!
    BCM21351_usb2nd.fg, Type: 2nd Boot Loader, Rev: 513.11.24.0, Algo: BB5
    Using NEW BB5 FLASHING PROTOCOL
    Transmission Mode Requested: Control USB, Accepted: Control USB
    FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
    FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
    FlashChip[0,CMT]: 0x0020003000000131, ST, NOR
    FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
    FlashChip[0,CMT]: 0x0020003000000131, ST, ONENAND
    Requested Algorithm: XSR 1.6 (CMT)
    Sending Auxiliary Loader...
    Auxiliary Loader Sent!
    Loader: RAPxx CommonBoot v1.07 (C) 2011 KarwosLabs
    Custom loader running OK! Working...
    Cyclone Server (1.0.0.676), Cyclone Box Team 2008-2011 - Ready.
    If phone doesn't powering into Local Mode now for some reason do following:
    1. Re-insert battery
    2. Power it on, when asked use Ovi/Pc Suite Mode
    Readed OK, Saving to "48400406073ECC4443B83B4151F972ABA08B3D66.C0003160 "
    Checking SUPERDONGLE...
    SUPERDONGLE FOUND AND CHECKSUM OK! PASSED!
    Checking SIMLOCK...
    Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
    Checking MCU&DSP TIMESTAMPS...
    MCU&DSP TIMESTAMPS FOUND AND CHECKSUM OK! PASSED!
    Checking CMLA KEYS...
    Failed to decode Security Section, Box Reported: Security Section Not Found (SL3 phone?)
    Checking ECC KEYS...
    ECC KEYS FOUND AND CHECKSUM OK! PASSED!
    Checking DIV KEYS...
    DIV KEYS FOUND AND CHECKSUM OK! PASSED!
    Analyze finished!


    PS1: Server connection and 10 credits (with 100 credits threshold) required to perform Broadcom Uni Data dump.

    PS2: After reading uni data, all operations is standalone (just likely previous basing upon cached data)

    PS3: Server charged credits, but my phone got disconnected during hash read operation, and hash not readen. What to do, what to do? If your account has been charged, the data generated at server are cached too... That means you can repeat process again (previously charging battery, i.e.), server transaction will be succeeded and no credits charged.

    Box firmware v01.82 is required to use this update.
    Software and loaders should be automatically updated.
    In case if you have aborted your update process, and now having problem with running app - you can download [You must be registered and logged in to see this link.] and place it in your Cyclone directory...

    MORE COMING !!!
    Best Regards,
    Cyclone Box Team
    mAk0y
    mAk0y
    Administrators
    Administrators


    Location : tiendaan laoag
    Posts : 55

    Cyclone Update Post Only HERE!!! Empty Re: Cyclone Update Post Only HERE!!!

    Post by mAk0y Thu Dec 08, 2011 11:26 am

    hello

    Broadcom Unlocking (via LBF Hash Read)/SX4 Authorization/SD Repair/etc
    is now fully FREE and STANDALONE, just simply as previous models.
    No internet connection and credits needed

    Just to remind Cyclone is one box which support all of hashes free and standalone now
    This includes reading data from RAP3Gv3, RAP3Gv4, RAPUv1, RAPUv21
    (world's first), Broadcom, XGold1, and shortly from XGold2 (maybe free,
    maybe with credits, we'll decide).

    NOTE
    No firmware upgrade is needed. Just run Cyclone and it will auto-update main exe + loaders.

    Make sure you have latest installer installed, if not, grab one from [You must be registered and logged in to see this link.]

    Box Firmware version required: v01.82 (from Nov 12)

    No Box FW Upgrade needed if u have that version (1.82).



    Best Regards,
    Cyclone Box Team
    mAk0y
    mAk0y
    Administrators
    Administrators


    Location : tiendaan laoag
    Posts : 55

    Cyclone Update Post Only HERE!!! Empty Re: Cyclone Update Post Only HERE!!!

    Post by mAk0y Wed Dec 21, 2011 4:13 pm

    21-12-2011 CycloneBox Installer v1.17 with Xperia Addon and more



    =====================
    Installer v1.17
    20.12.2011
    =====================


    SE Xperia Unlocker introduced (this is 3rd party addon)
    Supported Phones :
    Xperia X10 Mini - E10i
    Xperia X10 Mini Pro - U20
    Xperia X8 - E15i
    Xperia W8 - E16 - E16i
    Xperia X10
    Xperia X10i
    Xperia X10a
    Docomo SO-01B
    All These Phones supported without TEST POINT

    - Added Real time SE Xperia Unlocker account Creator in 'Credits' tool.
    (This is the best option for Online web shop resellers as Addon works
    without Box)Reseller can generate accounts real time with box)
    10 Cyclone credits = 1 Xperia phone log
    - BB5 FBUS/USB Loaders v11.40.00 Introduced
    - Introduced previous updates (standalone and free Broadcom unlocking, RAPUv21, etc)

    - PM Protection is now unticked by default
    - PM Protection is automatically unticked during SX4 operations
    - Full Erase for New Protocol APE phones fixed (wrong CMT Flash Device Index selected)
    -Added New bright skin
    - Minor changes and Bugfixes


    Download Links
    [You must be registered and logged in to see this link.]


    br
    CycloneBox Team

    Sponsored content


    Cyclone Update Post Only HERE!!! Empty Re: Cyclone Update Post Only HERE!!!

    Post by Sponsored content


      Current date/time is Fri Oct 04, 2024 4:03 pm