Home
RCD Tools - changes in relation to previous version:
- New firmware for CLIP, Box 2 Plus (automatic update after launch, do not interrupt)
- Added support for SPI and Microwire Memory in Box 2 Plus, and CLIP (Read & Write modes for 8 / 16 bit)
- Added support for SPI serial flash memory (25FL128)
- The ability to read through the interface 4-wires and 3-wires (schematics stored in Programmer bookmark)
- Detection of connected memory for Microwire
- Added ability to put direct links into tool
- Added ability to decode through Direct mode for uW and SPI (code reading goes after choosing Direct - Read Info, option will be visible only for
models confirmed by users eg. PU-2294)
- Swap Buf. - additional button to swap memory in Dump mode (after use the program again executes the code reading algorithm, this time for inverted bytes)
- Direct Mode is parametrized by Bus speed and Device address
- Added information about the differences in file size, RCD informs what is to be valid
- Added connection diagrams for new protocols directly in the tool
- Programmer tab will store all the possible protocols supported by Clip
- Main menu improvement (works more stable and faster)
- The program remembers the chosen model, you don't need to choose again if dump is bad
- Added option to reload the file from the dump
- Scrollbar in the main menu works as it should and does not move into the void
Additional options:
- Installation Set (automatic installation of drivers, software, Clip applications and manager)
- The ability to view supported models without Clip, Key, Box (Demo Version)
Complete list of added memory types:
- SPI: 95010, 95020, 95040, 95080, 95160, 95320, 95640, 95128, 95256, 95512
- Flash SPI: 25FL128
- Microwire: 93c06, 93C46, 93C56, 93C66, 93C76, 93C86
Rcd, Rcdpro, Security Installer: [You must be registered and logged in to see this link.]
Martech Team
[You must be registered and logged in to see this link.]
- New firmware for CLIP, Box 2 Plus (automatic update after launch, do not interrupt)
- Added support for SPI and Microwire Memory in Box 2 Plus, and CLIP (Read & Write modes for 8 / 16 bit)
- Added support for SPI serial flash memory (25FL128)
- The ability to read through the interface 4-wires and 3-wires (schematics stored in Programmer bookmark)
- Detection of connected memory for Microwire
- Added ability to put direct links into tool
- Added ability to decode through Direct mode for uW and SPI (code reading goes after choosing Direct - Read Info, option will be visible only for
models confirmed by users eg. PU-2294)
- Swap Buf. - additional button to swap memory in Dump mode (after use the program again executes the code reading algorithm, this time for inverted bytes)
- Direct Mode is parametrized by Bus speed and Device address
- Added information about the differences in file size, RCD informs what is to be valid
- Added connection diagrams for new protocols directly in the tool
- Programmer tab will store all the possible protocols supported by Clip
- Main menu improvement (works more stable and faster)
- The program remembers the chosen model, you don't need to choose again if dump is bad
- Added option to reload the file from the dump
- Scrollbar in the main menu works as it should and does not move into the void
Additional options:
- Installation Set (automatic installation of drivers, software, Clip applications and manager)
- The ability to view supported models without Clip, Key, Box (Demo Version)
Complete list of added memory types:
- SPI: 95010, 95020, 95040, 95080, 95160, 95320, 95640, 95128, 95256, 95512
- Flash SPI: 25FL128
- Microwire: 93c06, 93C46, 93C56, 93C66, 93C76, 93C86
Rcd, Rcdpro, Security Installer: [You must be registered and logged in to see this link.]
Martech Team
[You must be registered and logged in to see this link.]